Wooden Home Furniture
All designs

King Size Wooden Bed Design: King and Queen Size Ideas

12 designs Beds Checked 9 Oct 2026

A king size wooden bed design takes a 6 x 6.5 ft mattress (72 x 78 in), so the frame comes to about 6.5 x 7 ft. That is a lot of wood in one room. It only works when the room has the space for it, so measure first and choose the style later.

This gallery covers solid wood king beds, king beds with storage, queen beds for rooms that cannot take a king, and modern king beds with tall headboards. Each photo gives the timber or board, the main measurement, a suitable room and one tip to pass on to your carpenter.

For everyday styles in smaller rooms, see our double bed design gallery. If you only want a new headboard, our bed back design page has many more.

King Size Wooden Bed Design in Solid Wood

Solid wood makes the strongest king frame, because the side rails are long and carry two adults every night. These wooden king beds need a room of at least 12 x 13 ft.

King size bed design wooden, in teak with a three panel headboard and centre legs

Three raised teak panels make a headboard about 4 ft high, wide enough to balance the long frame. Natural polish keeps the golden grain on show, and it slowly deepens to a richer brown.

  • MaterialTeak, natural polish
  • Size6 x 6.5 ft, king
  • Fits12 x 13 ft master room

Carpenter tip: Add a middle rail with two legs under a king base, or the long span will sag within a year.

King size double bed design in sheesham with four short turned corner posts

Four turned posts rise about 8 in above the headboard and footboard. You get the look of an old poster bed without a canopy, which suits a room with a high ceiling and plain walls.

  • MaterialSheesham, walnut polish
  • Size6 x 6.5 ft, king
  • Fits13 x 14 ft bedroom

Carpenter tip: Turn each post from one piece of seasoned sheesham; posts glued from strips can split along the joint in dry winters.

Wooden king size bed design with wide sagwan planks laid across the headboard

Five wide sagwan planks run across the headboard between two end posts with small black bolt caps. The rustic look hides small dents and scratches, so it suits a busy joint family home.

  • MaterialSagwan, oil finish
  • Size6 x 6.5 ft, king
  • Fits12 x 14 ft bedroom

Carpenter tip: Leave a 2 mm gap between the planks so the wood can move in monsoon without cracking.

King Size Wooden Bed Design with Storage

A king base hides a lot. A box about 10 to 12 in deep takes quilts, spare pillows and a full season of woollens. More lift and drawer ideas are on our box bed design page.

King size wooden bed design with storage on a hydraulic lift from the foot

The whole mattress base rises on two gas lifts from the foot end, so you reach the box without moving the pillows. Walnut veneer on BWR ply keeps this big base lighter than solid wood.

  • MaterialBWR ply, walnut veneer
  • Size6 x 6.5 ft, king
  • Fits12 x 13 ft bedroom

Carpenter tip: Ask for lifts rated for a king mattress and fix a strap pull at the foot for an easy grip.

King bed design wooden with four deep side drawers in sheesham

Two deep drawers on each side run on full extension channels, so nothing has to be lifted. Each drawer needs roughly 2.5 ft of open floor next to the frame to pull out fully.

  • MaterialSheesham, honey polish
  • Size6 x 6.5 ft, king
  • Fits13 x 13 ft bedroom

Carpenter tip: Use 45 kg telescopic channels and make the drawers 9 in deep so folded quilts stand upright inside.

Wooden bed design king size with storage cubbies built into a deep headboard

A 10 in deep headboard holds lift up cubbies for medicines, chargers and spectacles, and its flat top works as a shelf. Below the mattress, two split lids open into the box.

  • MaterialBWR ply, oak laminate
  • Size6 x 6.5 ft, king
  • Fits12 x 14 ft bedroom

Carpenter tip: Fit stay hinges on the cubby flaps so they hold open and never drop shut on your fingers.

Queen Size Wooden Bed Design for Smaller Rooms

If the room is under 12 ft wide, pick a queen. A queen size double bed design takes a 5 x 6.25 ft mattress and fits a 10 x 11 ft room with walking space on three sides.

Queen size wooden bed design in sheesham with a low curved headboard

The headboard curves gently back at the top, so it is comfortable to lean on with one pillow. Without a footboard, the frame feels shorter in a compact room.

  • MaterialSheesham, natural polish
  • Size5 x 6.25 ft, queen
  • Fits10 x 11 ft bedroom

Carpenter tip: Shape the curve from glued sheesham layers, not one thick plank, so it stays true through humid months.

Wooden queen size bed design in teak with a pull out trundle bed below

A low trundle on castors rolls out from under the frame with a thin single mattress for a visiting relative. It saves buying a second bed in a two bedroom flat.

  • MaterialTeak, honey polish
  • Size5 x 6.25 ft + trundle
  • FitsGuest room, 10 x 12 ft

Carpenter tip: Keep the main side rail 16 in high so a 4 in single mattress on the trundle slides under easily.

Queen size bed design wooden in mango wood with a carved border headboard

A shallow carved vine border runs around a plain headboard panel. It feels traditional without deep carving that traps dust, and mango wood keeps the cost lower than teak.

  • MaterialMango wood, dark stain
  • Size5 x 6.25 ft, queen
  • Fits11 x 11 ft bedroom

Carpenter tip: Treat mango wood against borer before carving, then seal the carved grooves well so dust wipes off.

Modern King Size Bed Design Wooden with Tall Headboards

A headboard of 5 to 6 ft fills a high ceiling wall and draws every eye straight to the bed. These modern designs set a wooden or board frame under a headboard well above the usual 4.5 ft.

Modern king size bed with a 6 ft tall smoked oak veneer grooved headboard

Horizontal V grooves every 6 in break up a tall veneer panel, and the base sits on a recessed plinth. Plan it for a 10 ft ceiling so the panel does not crowd the room.

  • MaterialPly, smoked oak veneer
  • Size6 x 6.5 ft, king
  • Fits10 ft ceiling room

Carpenter tip: Fix the tall panel to the wall on battens, not only to the bed, so it can never tilt forward.

King size bed wooden design with tall grey fabric panels in a teak frame

Four tall padded panels in grey fabric sit inside a teak frame 5.5 ft high. You lean on the soft middle, while the wood edges take knocks from the vacuum cleaner.

  • MaterialTeak, grey fabric
  • Size6 x 6.5 ft, king
  • Fits13 x 13 ft bedroom

Carpenter tip: Screw each padded panel in from the back so a stained one can be taken out and re-covered alone.

King size double bed design latest style with a tall black matte PU headboard

A 5 ft headboard in matte black PU has a thin brass trim on its edges and sits on a walnut stained base. It looks bold against a light wall in a large flat.

  • MaterialMDF, matte black PU
  • Size6 x 6.5 ft, king
  • Fits12 x 14 ft bedroom

Carpenter tip: Black PU shows dust and swirl marks, so ask for a two coat matte finish and dust with microfibre.

How to Build a King Bed That Lasts

  • Centre support: a king base needs a middle rail on two or three legs. Without it the boards dip.
  • Base: two halves of 18 mm ply, or wooden slats with gaps for air. Two halves are easier to lift into a box.
  • Bolted joints: bed bolts at every corner so the frame opens up for shifting.
  • Headboard in parts: a 6.5 ft wide headboard may not fit in a lift or a narrow stair, so ask for two parts joined at the back.
  • Board for storage: BWR ply with PVC edge banding inside the box, since quilts trap damp in monsoon.

Solid teak or sheesham, veneer, padded headboards, hydraulic lifts and the extra foot of size all push up the cost. To compare timbers before you order, read our wood for furniture guide, and for joinery styles see wooden bed design.

Questions people ask

What is the size of a king size double bed design in India?

A king mattress is 6 x 6.5 ft, which is 72 x 78 in. The wooden frame around it comes to about 6.5 x 7 ft. Always confirm the mattress size before the carpenter cuts the rails.

Which should I choose, a queen size double bed design or a king?

Pick a queen for rooms around 10 x 11 ft, which covers most flats. A king makes sense in a 12 x 13 ft room or bigger, or when a child often sleeps with the parents.

What room do I need for a double bed design king size?

Plan for at least 12 x 13 ft. That leaves 2 ft on each side and at the foot, plus space for two side tables. In a smaller room a king blocks the wardrobe shutters.

Which wood is best for a wooden king size bed design?

Teak resists termites and damp, so it suits humid cities. Well seasoned sheesham is hard and heavy with strong grain. For a lighter frame with storage, BWR ply with veneer or laminate works well.

Is a double bed king size design with storage hard to open?

Not with good hydraulic lifts rated for the weight of a king mattress. Side drawers are even easier when the floor next to the frame is free for about 2.5 ft. Split lids also help, since each half is lighter.

Will a king bed fit through my lift and stairs?

The rails and base usually fit, but a one piece headboard often does not. Ask your carpenter to build the headboard in two parts and bolt the whole frame so it opens up on shifting day.

Keep browsing