Wooden Home Furniture
All designs

Wardrobe Laminate Design: Mica, Sunmica, Acrylic and Veneer Ideas

20 designs Wardrobes and almirahs Checked 9 Oct 2026

A good wardrobe laminate design decides how your bedroom looks every single day, so choose it slowly. Laminate, which most carpenters call sunmica or mica, is a thin decorative sheet pressed onto plywood shutters. It is easy to clean and takes daily use well.

This sunmica design wardrobe gallery has 20 original designs, grouped by material and finish. Each card lists the board, finish, size and room, so you can show it to your carpenter. For the full body and layout of the unit, see our wardrobe design gallery. If you are planning shades and pairs of colours, our double colour wardrobe design page covers colour combinations in detail.

Wood Grain Wardrobe Laminate Design

Wood grain laminate gives the look of veneer for less and needs almost no care, the safest pick for a joint family.

Wardrobe laminate design in deep rosewood tone wood grain with long bar handles

A deep rosewood tone grain with matching long bar handles looks close to solid sheesham from a few steps away. A good choice for a parents' room.

  • MaterialBWR ply, rosewood grain
  • Size8 ft x 7 ft, 4 door
  • Fits12 x 12 ft bedroom

Carpenter tip: Cut all four shutter sheets with the grain running the same way before pressing, or doors look patchy.

Light ash wood grain wardrobe laminate design on two sliding shutters with black profile

Pale ash grain keeps a narrow room bright, and the thin black aluminium profile guards the shutter edges from knocks on the sliding track.

  • MaterialBWR ply, ash grain
  • Size7 ft x 7.5 ft, sliding
  • Fits10 x 10 ft bedroom

Carpenter tip: Sliding units need 24 to 26 in depth. Fix the track first, then measure shutters for laminate.

Laminate wardrobe design in textured oak running full height to the ceiling

Textured oak with a raised grain feel runs from skirting to ceiling, with loft shutters lined up with the doors below. It makes a low room look taller.

  • MaterialBWR ply, textured oak
  • Size7 ft x 9.5 ft high
  • FitsFlat with 9.5 ft ceiling

Carpenter tip: Keep loft and door joints in one straight line. Even a 3 mm shift shows on grain laminate.

3 door wardrobe laminate design in smoked teak grain with a horizontal grain loft

Smoked teak grain runs up the three doors and turns sideways on the loft, so the top reads as a separate band. Suits a 10 ft ceiling bedroom.

  • MaterialBWR ply, smoked teak
  • Size6 x 7 ft + 2.5 ft loft
  • Fits10 ft ceiling bedroom

Carpenter tip: Order the loft sheets separately so the grain can run sideways. One sheet cannot give both directions.

Matte and Suede Wardrobe Mica Design

Matte and suede sheets are the quiet side of wardrobe mica design. They have no shine, hide fine scratches and feel soft to touch, which suits a bedroom used all day.

Wardrobe mica design in taupe suede laminate with anti fingerprint finish and knob handles

Taupe suede sheet with an anti fingerprint layer stays clean around the handles even with daily use. A sensible pick for a busy master bedroom.

  • MaterialBWR ply, taupe suede
  • Size8 ft x 7 ft, 4 door
  • Fits12 x 13 ft bedroom

Carpenter tip: Suede sheets mark under a hot press iron. Use the cold press or a pressing cloth on site.

Modern wardrobe pattern design with concrete texture matte laminate on three shutters

A concrete look sheet with soft cloudy patches gives an industrial feel without real cement. It hides dust well in a flat near a busy road.

  • MaterialBWR ply, concrete matte
  • Size6 ft x 7 ft, 3 door
  • Fits10 x 11 ft bedroom

Carpenter tip: Stone texture sheets have a printed direction. Arrow mark the back of each before cutting shutters.

Almirah mica design with leather texture laminate shutters and stitched line grooves

Leather texture laminate in tan brown with grooved lines like stitching gives a small almirah a rich, grown up feel. Works in a study or guest room.

  • MaterialBWR ply, leather texture
  • Size3 ft x 6.5 ft, 2 door
  • FitsGuest room corner

Carpenter tip: Cut the grooves with a router before pressing, then fold the laminate in with a heat gun.

Modern Acrylic Wardrobe Design and High Gloss Shutters

Acrylic gives a glassy finish that bounces light around a small room. It costs more than laminate and shows finger marks, so it suits an adults' room better than a busy family room.

Modern acrylic wardrobe design with high gloss white shutters and groove handles

High gloss white acrylic with a top groove handle gives a clean, flat front. In a small room it reflects window light and feels bigger.

  • MaterialBWR ply, white acrylic
  • Size6 ft x 7 ft, 3 door
  • Fits10 x 10 ft bedroom

Carpenter tip: Keep the protective film on until all fitting is done. Acrylic scratches easily during site work.

Acrylic sheet wardrobe design in cream gloss with a G profile handle on each door

Cream gloss acrylic with a G profile cut into the top edge needs no outside handle. The warm cream reflects less glare than bright white.

  • MaterialBWR ply, cream acrylic
  • Size8 ft x 7 ft, 4 door
  • Fits12 x 13 ft bedroom

Carpenter tip: Order shutters with factory pressed acrylic and laser edge banding. Site pressed acrylic often shows bubbles.

High gloss grey acrylic wardrobe design with a full length mirror shutter in the centre

Two grey gloss shutters on each side of one full length mirror door mean you need no separate dressing mirror. Good for a compact flat.

  • MaterialBWR ply, grey acrylic
  • Size7.5 ft x 7 ft, 5 door
  • Fits11 x 11 ft bedroom

Carpenter tip: Bond the mirror with neutral silicone and add two steel clips at the bottom edge for safety.

Pastel mint matte acrylic wardrobe with matching drawers and small brass knob handles

Matte acrylic in pastel mint feels smooth like paint but cleans like laminate. The three drawers below use the same sheet for one calm front.

  • MaterialBWR ply, matte acrylic
  • Size5 ft x 7 ft, 2 door
  • FitsGuest room, 9 x 10 ft

Carpenter tip: Matte acrylic hides finger marks better than gloss. Clean with a soft cloth, never a scrubber.

Fluted Laminate Wardrobe Design

Fluted laminate has raised vertical ribs that catch light and add texture. Use it on one or two shutters as a feature, or on a small almirah, so the wall does not feel busy.

Fluted laminate wardrobe design with walnut ribbed centre shutters and plain side doors

Two walnut fluted shutters in the middle with plain matching side doors give texture without crowding the room. Pair it with a simple bed.

  • MaterialBWR ply, fluted walnut
  • Size8 ft x 7 ft, 4 door
  • Fits12 x 12 ft bedroom

Carpenter tip: Fluted sheets are thicker, so use longer hinge screws and check door gaps before final fixing.

Luxury fluted wardrobe design in beige laminate running full height with a gold line

Beige ribs run floor to ceiling with a thin gold strip at the loft joint. It suits a large bedroom with plain walls and simple curtains.

  • MaterialBWR ply, beige fluted
  • Size9 ft x 10 ft high
  • Fits14 x 15 ft bedroom

Carpenter tip: Dust settles in the ribs. Clean with a soft paint brush once a week, then wipe with a dry cloth.

Fluted mica wardrobe design on a light oak ribbed almirah with round wooden knobs

Wide half round ribs in light oak cover both doors of this small almirah. The bold ribs look like carved wood and suit a rented flat.

  • MaterialMR ply, oak ribbed sheet
  • Size3 ft x 6 ft, 2 door
  • FitsRented flat, dry room

Carpenter tip: Flexible ribbed sheets crack if bent sharp. Bend them over a rounded edge, never a square corner.

Sunmica Design for Wardrobe and Almirah Patterns

Pattern sheets give the latest mica design for wardrobe fronts without paint or carving. The same sheets work as a sunmica design for almirah shutters. Check a wardrobe sunmica design catalogue, then ask for a big sample.

Wardrobe sunmica design with a geometric line pattern in grey on white shutters

A thin grey line pattern runs over three shutters and meets cleanly at the joints. It is a modern wardrobe pattern design that still stays quiet.

  • MaterialBWR ply, pattern sunmica
  • Size6 ft x 7 ft, 3 door
  • Fits10 x 11 ft bedroom

Carpenter tip: Lay all shutters flat side by side and mark where the lines meet before pressing the sheet.

Almirah sunmica design with cane print laminate shutters and a teak grain frame

Cane print laminate gives the look of woven rattan without the sagging and dust. A teak grain frame keeps it warm and homely.

  • MaterialBWR ply, cane print
  • Size3 ft x 6.5 ft, 2 door
  • FitsSmall bedroom corner

Carpenter tip: Real cane sags in humid months. The printed sheet gives the same look and stays flat.

Wardrobe mica design with white marble print laminate and thin gold strips

White marble print mica with thin gold strips between the shutters looks rich in a room with marble flooring. Keep the rest of the room plain.

  • MaterialBWR ply, marble laminate
  • Size8 ft x 7 ft, 4 door
  • Fits13 x 14 ft bedroom

Carpenter tip: Pick gloss marble laminate with a matching edge band. Matte marble print looks flat and printed.

PU Finish and Veneer Wardrobe Design

When a sheet is not enough, carpenters turn to PU paint on MDF or real wood veneer on ply. Both cost more and take longer on site, but they give a finish laminate cannot copy.

PU finish wardrobe design with shaker style grooved shutters in matte putty paint

Shaker style frames are routed into HDHMR shutters, then sprayed in matte putty PU. The grooves give a soft shadow that flat laminate never shows.

  • MaterialHDHMR, matte PU paint
  • Size7 ft x 7 ft, 4 door
  • Fits11 x 12 ft bedroom

Carpenter tip: Use moisture resistant HDHMR, not plain MDF, and seal every edge with primer before the PU coats.

Veneer wardrobe design with book matched walnut veneer shutters and matte polish

Walnut veneer is laid in mirror image pairs, so the grain meets like an open book across each pair of doors. Real wood depth for a large master bedroom.

  • MaterialBWR ply, walnut veneer
  • Size9 ft x 7 ft, 4 door
  • Fits13 x 15 ft bedroom

Carpenter tip: Number veneer leaves in order from the bundle. Book matching fails if sheets get shuffled during pressing.

Teak veneer wardrobe with horizontal V grooves and a natural polish finish

Burma teak veneer with thin horizontal V grooves every 8 in gives a slatted look on flat ply. Natural polish keeps the golden tone honest.

  • MaterialBWR ply, teak veneer
  • Size6 ft x 7 ft, 3 door
  • Fits10 x 12 ft bedroom

Carpenter tip: Cut V grooves after pressing veneer, then polish. Grooves cut first tear the thin veneer edge.

Laminate Thickness, Edge Banding and Reading a Catalogue

  • Outer sheet: ask for 0.8 to 1 mm laminate on the outside. Thinner sheets chip at corners and show board waves.
  • Inner liner: the inside face of each shutter needs a 0.8 mm liner. Without it, the door bends because only one side is sealed.
  • Board: BWR plywood for bedrooms in humid cities. Skip particle board for shutters, hinge screws loosen.
  • Edge banding: 2 mm PVC edge band in a matching shade on every visible edge. It keeps damp out of the ply.
  • Catalogue codes: each sheet has a number, a finish code (SF for suede, HG for high gloss, MT for matte) and a thickness. Write all three on your order, because the same shade comes in different textures.

Choose handles at the same time as the laminate, since a gold profile or black bar changes the look. Our wardrobe handle design page shows options, and the wood and board guide explains plywood grades.

Care in Monsoon and Strong Sun

Laminate itself does not soak water, but open edges and the board behind do. In monsoon, wipe any water drops on the doors at once and keep the unit 2 to 3 in away from a damp outer wall.

Strong afternoon sun fades pastel and dark sheets and yellows veneer polish over time. Use a sheer curtain on west windows. Clean acrylic and gloss shutters with a soft microfibre cloth and plain water, never a scrubber or harsh cleaner. For more tips see wooden furniture care, and plan the shelves behind these shutters with our wardrobe inside design ideas.

Questions people ask

Which is better for a wardrobe, laminate or acrylic?

Laminate is tougher and hides small scratches. Acrylic gives a deep glossy look but shows finger marks easily. Many people use laminate on most doors and acrylic on one or two feature shutters.

Is PU finish or veneer better than sunmica for a wardrobe?

PU and veneer look richer up close, but they cost more, take longer to finish and need more care. Veneer needs repolishing every few years, and PU can chip if knocked. Sunmica is the practical pick for most bedrooms.

How thick should wardrobe sunmica be?

Use 0.8 to 1 mm laminate on the outside and a 0.8 mm liner on the inner face of the shutter. This balance stops doors from bending.

Is a fluted laminate wardrobe design hard to clean?

It needs a little more care because dust sits in the grooves. Run a soft dry paint brush along the ribs once a week, then wipe with a dry cloth.

Which almirah mica design hides dust and marks best?

Medium wood grains, suede finishes and stone or concrete textures hide dust and finger marks well. High gloss sheets and plain dark matte show every mark.

What is the latest mica design for wardrobe shutters right now?

These days fluted and ribbed sheets, cane print, suede textures, concrete looks and soft matte acrylic are popular. Wood grains like walnut and light oak remain the safest choice for a long term look.

Keep browsing