PVC TV Unit Design Ideas: Modern Units, Panel Walls, UPVC and WPC
14 designs TV units Checked 9 Oct 2026
A PVC TV unit design makes sense when the hall wall gets damp every monsoon or termites have already eaten one cupboard. PVC foam board and WPC do not soak up water, so they do not swell, peel or rot like ply on a wet wall.
Browse these modern PVC TV unit design latest images below. Each one names the board, the wood look on it, the size and the room it suits, so your mistri knows exactly what to make. Many PVC units are finished with a wood grain laminate or foil, so they look like wood from the sofa. For panelled walls in real wood, marble and cement, see our TV unit wall design page.
Modern PVC TV Unit Design
A modern PVC TV unit design keeps lines flat and simple: floating consoles, push open drawers and one wood look strip for warmth. PVC foam board takes laminate well, so you get the colour you want on a waterproof core.

An 18 mm PVC foam board console with walnut laminate floats 12 in above the floor, so the mop never touches it. Push open drawers keep the front clean with no handles.
- MaterialPVC foam board, walnut
- Size7 ft long, 15 in deep
- FitsHall, 10 x 12 ft
Carpenter tip: Hang the console on a steel angle screwed into brick, because foam board cannot carry weight on screws alone.

A white high gloss PVC sheet covers the TV wall, and one tall oak grain strip with a warm light runs down the left side. The gloss bounces light into a dark hall.
- MaterialPVC sheet, oak grain
- Size8 ft wide, 8 ft high
- FitsNorth facing hall
Carpenter tip: Leave the factory film on the gloss sheet until the last screw is in, as it scratches easily.

Large charcoal marble print PVC sheets with thin brass joint strips cover the wall, and a teak grain ledge runs below the TV. It reads like polished stone yet weighs far less than tiles.
- MaterialPVC marble sheet, teak
- Size9 ft wide, 9 ft high
- FitsHall, 12 x 14 ft
Carpenter tip: Fix glossy marble sheets on a flat 6 mm ply backing, since any bump in the plaster shows on gloss.

A simple PVC TV unit design for a rented flat: one maple grain console shelf and a small open box above it for the router. It fits in a single day of work.
- MaterialPVC board, maple grain
- Size5 ft long, 12 in deep
- FitsRented 1 BHK hall
Carpenter tip: Keep open shelf spans under 30 in, or add a centre bracket, since PVC board sags sooner than ply.
PVC Panel TV Unit Design and Louver Walls
A TV unit design with PVC panel cladding covers a stained or uneven wall in a day. Louvers are fluted strips that clip together, and wood grain louvers look closest to real timber.

Oak grain PVC louvers run floor to ceiling across a 9 ft wall, with a thin black ledge for the soundbar. The ribs hide joints, so the wall reads as one surface.
- MaterialPVC louvers, oak grain
- Size9 ft wide, 10 ft high
- FitsHall with 10 ft ceiling
Carpenter tip: Start the first louver with a spirit level, or the error grows across the whole wall.

Walnut grain louvers cover only a 5 ft centre band behind the TV, and the rest of the wall stays painted grey. This uses fewer panels and still frames the screen.
- MaterialPVC louvers, walnut
- Size5 ft band, 8 ft high
- FitsSmall hall, 10 ft wall
Carpenter tip: Finish both side edges of the louver band with matching end caps so the hollow core does not show.

Cream PVC wall panels with raised moulding boxes give a classic look without plaster work. A teak grain console with cane print shutters keeps it from looking too plain.
- MaterialPVC panels, teak grain
- Size8 ft wide, 8.5 ft high
- FitsHall, 11 x 13 ft
Carpenter tip: Stick PVC mouldings with a flexible adhesive, not nails, so they do not crack in summer heat.

Ash grain louvers climb the wall and bend onto a 3 ft strip of the false ceiling above the TV. It makes a low hall feel taller and hides the ceiling wiring.
- MaterialPVC louvers, ash grain
- Size7 ft wide, wall + 3 ft
- FitsHall, 9.5 ft ceiling
Carpenter tip: Fix ceiling louvers to a metal grid with screws every 16 in so they never droop.
UPVC and WPC TV Unit Design for Damp Walls
A WPC TV unit design is the safest pick for an outer wall that leaks or a ground floor wall with rising damp. A UPVC TV unit design uses rigid profiles that do not swell at all, finished in a wood foil.

This WPC TV unit design, latest in many ground floor flats, stands on a wall that gets wet each monsoon. WPC holds hinges far better than foam board, so the shutters stay true.
- MaterialWPC board, teak laminate
- Size6 ft long, 18 in high
- FitsGround floor hall
Carpenter tip: Pre-drill every screw hole in WPC and use stainless screws, as it can crack near the edges.

Rigid UPVC frames wrapped in walnut foil hold frosted glass shutters on a low unit. The profiles are welded at the corners like windows, so damp cannot open the joints.
- MaterialUPVC frame, walnut foil
- Size6.5 ft long, 20 in high
- FitsCoastal flat hall
Carpenter tip: Order the UPVC frames from a window fabricator to exact size, since they cannot be trimmed on site.

Dark sheesham look WPC louvers cover a wall shared with a bathroom, and the console stands on steel legs 6 in above the floor. Water from mopping never reaches the board.
- MaterialWPC louvers, sheesham
- Size7 ft wide, 8 ft high
- FitsWall next to bathroom
Carpenter tip: Leave a 10 mm gap at the floor and ceiling ends of WPC louvers so they can expand.
Living Room PVC TV Unit Design
A living room PVC TV unit design can still give a joint family plenty of storage. Use PVC board for carcass and back panels, and pick a wood grain finish that matches your doors.

A tall oak grain PVC cabinet on one side holds board games, files and spare bulbs, and a low console runs under the TV. The cabinet back stays safe on a damp wall.
- MaterialPVC board, oak laminate
- Size9 ft wide, 7 ft high
- FitsJoint family hall
Carpenter tip: Use mounting plate hinges with long screws on PVC board shutters, and add a ply strip where hinges sit.

White PVC shutters cut on a CNC in a jaali pattern sit in a teak grain frame, so the router and set top box get air. Foam board cuts cleanly and needs no edge polish.
- MaterialPVC board, teak grain
- Size7 ft long, 18 in high
- FitsHall, 11 x 12 ft
Carpenter tip: Back each jaali with a thin fabric or mesh so dust does not settle on the electronics inside.

Matte grey PVC shutters pair with walnut grain open boxes on both sides of the TV for plants and small brass pieces. The grey finish does not show dust as much as white.
- MaterialPVC board, grey + walnut
- Size10 ft wide, 6 ft high
- FitsLiving room, 12 ft wall
Carpenter tip: Seal every PVC board edge with matching edge banding, or cut foam edges collect dirt.
Checking for Sag, Fading and Weak Fittings
- Thickness: ask for 18 mm board for the console top and shelves. Thin 12 mm sheets bend under a soundbar.
- Press test: press the board edge with your thumb. Good foam board feels hard and heavy for its size, not soft.
- Shelf span: keep shelves under 30 in between supports, and add a metal angle under long tops.
- Heat: keep 4 in of air above the TV vents and set top box. PVC softens near steady heat.
- Sun: white and light grey PVC can turn yellow in strong afternoon sun. Use a laminate or foil with UV protection, or hang a curtain.
- Hinges: use mounting plate hinges and long screws, or glue in a ply strip where hinges sit.
For a lighter budget unit, see simple TV unit design, and for bigger hall layouts browse TV unit design for hall.
Questions people ask
Is a PVC TV unit design strong enough for a 65 inch TV?
The TV should never hang on the PVC panel. Fix the bracket straight into brick through a gap or a ply block in the panel. The PVC console only carries the set top box and small items.
Which is better, a WPC TV unit design or a PVC one?
WPC is denser and holds screws and hinges better, so it suits shutters and consoles. PVC foam board is lighter and costs less, so it suits wall cladding and back panels. On a very damp wall, WPC is the safer choice.
What is a UPVC TV unit design?
It uses rigid UPVC profiles, the same kind used for windows, to make shutter frames with glass or board inside. A wood grain foil covers the frames. It never swells, but it must be made to exact size by a fabricator.
Does a PVC panel TV unit design fade in sunlight?
Light coloured PVC can yellow if afternoon sun hits it every day. Wood grain and darker panels show it less. Choose sheets with UV coating and keep a curtain on west facing windows.
Can PVC board take laminate or paint like plywood?
Yes, it takes laminate with the right adhesive, which is how most wood look PVC units are made. Paint needs light sanding and a primer made for plastic. Ask your carpenter which adhesive he will use before work starts.
How do I clean a PVC TV unit?
Wipe it with a damp cloth and mild soap, then dry it. Avoid thinner, acetone and scrub pads, which dull gloss and mark wood grain prints. Dust louver grooves with a soft brush every week.





